基于Kriging模型的造纸法再造烟叶筛分工艺参数优化方法
Optimization of sieving process parameters for paper-based reconstituted tobacco based on Kriging model
-
摘要:为充分考虑造纸法再造烟叶筛分工艺参数的随机变化,以水流速度和烟浆固含量为设计参数,以筛分后12目以上纤维质量占比和50目以下纤维质量占比为性能响应,提出了基于Kriging模型的造纸法再造烟叶筛分工艺参数优化方法。首先,以当前工艺参数为继承点进行继承拉丁超立方采样和筛分实验,在此基础上构建初始Kriging模型以拟合水流速度和烟浆固含量与12目以下纤维质量占比和50目以上纤维质量占比间的隐式关系;其次,采用局部自适应采样方法开展序列采样以提高Kriging模型在优化迭代关键点的精度;最后,利用蒙特卡罗仿真-序列二次规划计算最优的再造烟叶筛分工艺参数。结果表明:优化得到的水流速度和烟浆固含量分别为6.31 L/min和0.53%,该工艺参数下的12目以下纤维质量占比为13.72%,较优化前提升了7.19%;50目以上纤维质量占比为17.65%,较优化前降低了4.13% 。该方法能够满足造纸法再造烟叶筛分工艺参数优化需求。Abstract:In order to fully consider the random variation of sieving process parameters,this paper constructs the reliability-based optimization model for reconstituted tobacco process parameters,which taking the percentage of fibers below 12 mesh as the optimization objective,water flow rate and pulp concentration as the design parameters,and the percentage of fibers over 50 mesh as the probabilistic constraint. Firstly, the current process parameters are used as inheritance points for Latin hypercube sampling and screening experiments. Based on this, an initial Kriging model is constructed to fit the implicit relationship between water flow velocity, smoke slurry solid content, and the proportion of fiber mass below 12 mesh and above 50 mesh. And local adaptive sampling (LAS) was carried out to update the Kriging model to ensure the approximate accuracy of key positions at optimization iteration.Finally,Monte Carlo simulation (MCS)-Sequential quadratic programming (SQP) was used to solve the optimization model of screening process parameters. The results indicated that the optimized water flow rate and pulp concentration were 6.31 L/min and 0.53% , respectively. Under this process parameter, the proportion of fiber below 12 mesh was 13.72% , which was 7.19% higher than before optimization. The proportion of fibers over 50 mesh was 17.65% , which was a decrease of 4.13% compared to before optimization. This method could meet the optimization requirements of screening process parameters for paper making reconstituted tobacco leaves.
-
- [1]
韩文佳,赵传山.造纸法烟草薄片发展现状[J].黑龙江造纸,2007,35(4):47-49.
- [2]
HU L Z,ZHANG S J,YU X P,et al.Estimation of cut stalk filaments and slices content in blends of tobacco filaments by uniform design-PLS-NIR method[J].Acta Tabacaria Sinica,2010,16(2):26-30.
- [3]
董高峰,田永峰,尚善斋,等.用于加热不燃烧(HnB)卷烟的再造烟叶生产工艺研究进展[J].中国烟草学报,2020,26(1):109-117.
- [4]
高金玲,李书芳,朱国成,等.真空回潮工序对造纸法再造烟叶的质量影响[J].郑州轻工业学院学报(自然科学版),2012,27(5):55-58.
- [5]
WANG L,WEN Y B,SUN D P.Study on the decrease of harmful substance in paper-process reconstituted tobacco sheet[C]//Advanced Manufacturing Technology.Part 3.:Trans Tech Publications,2011,314:2338-2343.
- [6]
刘恩芬,王春琼,彭丽娟,等.造纸法再造烟叶质量监控技术开发应用[J].纸和造纸,2022,41(4):23-27.
- [7]
MCADAM K G,GREGG E O,LIU C,et al.The use of a novel tobacco-substitute sheet and smoke dilution to reduce toxicant yields in cigarette smoke[J].Food and Chemical Toxicology:An International Journal Published for the British Industrial Biological Research,2011,49(8):1684-1696.
- [8]
罗一鸣,张献英,何国兴.造纸法再造烟叶加工技术分析[J].广东化工,2021,48(14):104-105.
- [9]
王诗雨,张柯,王乐,等.加热卷烟不同工艺再造烟叶等温干燥动力学研究[J].烟草科技,2021,54(9):80-89.
- [10]
孙德坡,尚善斋,赵伟,等.造纸法再造烟叶萃取和涂布液工艺研究综述[J].郑州轻工业学院学报(自然科学版),2014,29(6):17-21.
- [11]
苏宗元.几种纤维筛分仪的介绍[J].天津造纸,1987(2):23-27.
- [12]
聂一平.影响卷烟中一氧化碳量的几种因素[J].烟草科技,1999(2):26-28.
- [13]
董浩,王澍,周明珠,等.卷烟表观燃烧性能质量状况分析[J].烟草科技,2022,55(4):70-78.
- [14]
薛洋.再造烟叶低浓打浆工艺研究[J].企业技术开发(下半月),2016,35(18):9-10
,13. - [15]
张婷婷,谢益民,瞿方,等.烟梗混合打浆工艺的研究[J].湖北造纸,2012(3):62-64.
- [16]
温洋兵,罗冲,胡惠仁,等.改善造纸法烟草基片松厚度的研究[J].中国造纸,2012,31(4):30-33.
- [17]
罗冲,温洋兵,胡惠仁,等.制浆工艺对造纸法烟草薄片性质的影响[J].纸和造纸,2012,31(7):37-40.
- [18]
LI X K,ZHU H,CHEN Z Z,et al.Limit state Kriging modeling for reliability-based design optimization through classification uncertainty quantification[J].Reliability engineering & system safety,2022,224:108539.
- [19]
MI X,LIANG G,SHAO X Y,et al.A generalised collaborative optimisation method and its combination with Kriging metamodels for engineering design[J].Journal of Engineering Design,2012,23(4/5/6):379-399.
- [20]
王瑾婷.基于GC-MS、GC×GC-MS、ICP-MS对辣椒中特征成分和特征元素的筛查方法研究[D].郑州:18新利直播 ,2022.
- [21]
张忠元,矫承轩,桑涛,等.车身响应面模型参数的拉丁超立方采样仿真[J].计算机仿真,2021,38(7):123-127.
- [22]
李晓科,马军,陈振中,等.基于继承拉丁超立方采样与局部Kriging近似的可靠性设计优化[J].计算机集成制造系统,2018,24(12):3107-3119.
- [23]
ZHENG J,SHAO X Y,LIANG G,et al.A hybrid variable-fidelity global approximation modeling method combining tuned radial basis function base and Kriging correction[J].Journal of Engineering Design,2013,24(7/9):604-622.
- [24]
LI X K,QIU H B,CHEN Z Z,et al.A local sampling method with variable radius for RBDO using Kriging[J].Engineering Computations,2015,32(7):1908-1933.
- [25]
BYEONG-SOO K,YONG-BIN L,DONG-HOON C.Comparison study on the accuracy of metamodeling technique for non-convex functions[J].Journal of Mechanical Science and Technology,2009,23(4):1175-1181.
- [26]
CHEN Z Z,QIU H B,GAO L,et al.A local adaptive sampling method for reliability-based design optimization using Kriging model[J].Structural and Multidisciplinary Optimization,2014,49:401-416.
- [27]
郭耀斌,张文明,张国芬.基于蒙特卡罗法的螺旋锥齿轮接触疲劳可靠性分析[J].农业机械学报,2008,39(4):157-159.
- [28]
王林军,邓启程.基于序列二次规划法的结构可靠度计算方法[J].组合机床与自动化加工技术,2018(11):12-15.
- [1]
-
点击查看大图
计量
- PDF下载量:9
- 文章访问数:886
- 引证文献数:0
下载:
